資源目錄里展示的全都有，所見即所得。下載后全都有,請放心下載。原稿可自行編輯修改=【QQ：401339828 或11970985 有疑問可加】 機0405 11號 馬吟川 指導老師：許寶杰 THE DESIGN OF PARALLEL KINEMATIC MACHINE TOOLS USING KINETOSTATIC PERFORMANCE CRITERIA http://arxiv.org/ftp/arxiv/papers/0705/0705.1038.pdf 1. INTRODUCTION Most industrial machine tools have a serial kinematic architecture, which means that each axis has to carry the following one, including its actuators and joints. High Speed Machining highlights some drawbacks of such architectures: heavy moving parts require from the machine structure high stiffness to limit bending problems that lower the machine accuracy, and limit the dynamic performances of the feed axes. That is why PKMs attract more and more researchers and companies, because they are claimed to offer several advantages over their serial counterparts, like high structural rigidity and high dynamic capacities. Indeed, the parallel kinematic arrangement of the links provides higher stiffness and lower moving masses that reduce inertia effects. Thus, PKMs have better dynamic performances. However, the design of a parallel kinematic machine tool (PKMT) is a hard task that requires further research studies before wide industrial use can be expected. Many criteria need to be taken into account in the design of a PKMT. We pay special attention to the description of kinetostatic criteria that rely on the conditioning of the Jacobian matrix of the mechanism. The organisation of this paper is as follows: next section introduces general remarks about PKMs, then is explained why PKMs can be interesting alternative machine tool designs. Then are presented existing PKMTs. An application to the design of a small-scale machine tool prototype developed at IRCCyN is presented at the end of this paper. 2. ABOUT PARALLEL KINEMATIC MACHINES 2.1. General Remarks The first industrial application of PKMs was the Gough platform (Figure 1), designed in 1957 to test tyres1. PKMs have then been used for many years in flight simulators and robotic applications2 because of their low moving mass and high dynamic performances. Since the development of high speed machining, PKMTs have become interesting alternative machine tool designs3, 4. Figure 1. The Gough platform In a PKM, the tool is connected to the base through several kinematic chains or legs that are mounted in parallel. The legs are generally made of either telescopic struts with fixed node points (Figure 2a), or fixed length struts with gliding node points (Figure 2b). Along with high-speed cutting's unceasing development, the traditional tandem type organization constructs the platform the structure rigidity and the traveling carriage high speed becomes the technological development gradually the bottleneck, but the parallel platform then becomes the best candidate object, but was opposite in the tandem engine bed, the parallel working platform had the following characteristic and the merit: (1) structure is simple, the price is low The engine bed mechanical spare part number is series connected constructs the platform to reduce largely, mainly by the ball bearing guide screw, the Hooke articulation, the ball articulation, the servo electrical machinery and so on common module is composed, these common modules may by the special factory production, thus this engine bed's manufacture and the inventory cost are much lower than the same function's traditional engine bed, easy to assemble and the transporting. (2) structure rigidity is high Because used closeness structure (closed-loop structure) to enable it to have high rigid and the high speed merit, its structural load streamline was short, but shouldered decomposes pulls, the pressure also to withstand by six connecting rods, by materials mechanics' viewpoint, when the external force was certain, the bracket quantity's stress and the distortion were biggest, the both sides inserted the (build-in) next best, came is again both sides Jan supports (simply-supported), next was the bearing two strength structure, what the stress and the distortion were smallest was the tensity two strength structure, therefore it had the high rigidity. Its rigidity load ratio is higher than traditional the numerically-controlled machine tool. (3) processing speed is high, the inertia is low If the structure withstands the strength will change the direction, (will be situated between tensity and pressure), two strength components will be most save the material the structure, but it will move to the moving parts weight to reduce to lowly and simultaneously will actuate by six actuating units, therefore machine very easy high speed, and will have the low inertia. (4) working accuracy is high Because it for the multiple spindle parallel organization composition, six expandable pole poles long alone has an effect to cutting tool's position and the posture, thus does not have the traditional engine bed (i.e. connects engine bed) the geometrical error accumulation and the enlargement phenomenon, even also has the being uniform effect (averaging effect); It has the hot symmetrical structural design, therefore the thermal deformation is small; Therefore it has the high accuracy merit. (5) multi-purpose flexible Is convenient as a result of this engine bed organization simple control, easily according to processing object, but designs it the special purpose machine, simultaneously may also develop the general engine bed, with realizes the milling, boring, processings and so on grinding, but may also provide the essential measuring tool to compose it the measuring engine, realizes engine bed's multi-purpose. This will bring the very big application and the market prospect, has the very broad application prospect in the national defense and the civil aspect. (6) service life is long Because the stress structure is reasonable, the moving part attrition is small, and does not have the guide rail, does not have the iron filings either the refrigerant enters the guide rail interior to cause it to scratch, the attrition or the corrosion phenomenon. (7) Stewart platform suits in the modular production Regarding the different machine scope, only need change the connecting rod length and the contact position, maintains also easily, does not need to carry on part's remaking and to adjust, only need the new organization parameter input. (8) transformation coordinate system is convenient Because does not have the entity coordinate system, the engine bed coordinate system and the work piece coordinate system transform depend on the software to complete completely, is convenient. When the Stewart platform applies in the engine bed and the robot, may reduce the static error (, because high rigidity), as well as dynamic error (because low inertia). But Stewart the platform inferiority lies in its working space to be small, and it has the singular point limit in the working space, but the serial operation platform, the controller meets time the singular point, accountant will figure out the actuation order which the drive is unable to achieve to create the ning error, but the Stewart platform will lose the support partial directions in the strange position the strength or moment of force ability, will be unable to complete the constant load object. Figure 2a. A bipod PKM Figure 2b. A biglide PKM 2.2. Singularities The singular configurations (also called singularities) of a PKM may appear inside the workspace or at its boundaries. There are two types of singularities5. A configuration where a finite tool velocity requires infinite joint rates is called a serial singularity. A configuration where the tool cannot resist any effort and in turn, becomes uncontrollable, is called a parallel singularity. Parallel singularities are particularly undesirable because they induce the following problems: - a high increase in forces in joints and links, that may damage the structure, - a decrease of the mechanism stiffness that can lead to uncontrolled motions of the tool though actuated joints are locked. Figures 3a and 3b show the singularities for the biglide mechanism of Fig. 2b. In Fig. 3a, we have a serial singularity. The velocity amplification factor along the vertical direction is null and the force amplification factor is infinite. Figure 3b shows a parallel singularity. The velocity amplification factor is infinite along the vertical direction and the force amplification factor is close to zero. Note that a high velocity amplification factor is not necessarily desirable because the actuator encoder resolution is amplified and thus the accuracy is lower. Figure 3a. A serial singularity Figure 3b. A parallel singularity 2.3. Working and Assembly Modes A serial (resp. parallel) singularity is associated with a change of working mode6 (resp. of assembly mode). For example, the biglide has four possible working modes for a given tool position (each leg node point can be to the left or to the right of the intermediate position corresponding to the serial singularity, Fig. 4a) and two assembly modes for a given actuator joint input (the tool is above or below the horizontal line corresponding to the parallel singularity, Fig. 4b). The choice of the assembly mode and of the working mode may influence significantly the behaviour of the mechanism5. Figure 4a. The four working modes Figure 4b. The two assembly modes 3. PKMs AS ALTERNATIVE MACHINE TOOL DESIGNS 3.1. Limitations of Serial Machine Tools Today, newly designed machine tools benefit from technological improvements of components such as spindles, linear actuators, bearings. Most machine tools are based on a serial architecture (Figure 5), whose advantage is that input/output relations are simple. Nevertheless, heavy masses to be carried and moved by each axis limit the dynamic performances, like feed rates or accelerations. That is why machine tools manufacturers have started being interested into PKMs since 1990. 3.2. PKMs Potentialities for Machine Tool Design The low moving mass of PKMs and their good stiffness allow high feed rates (up to 100 m/min) and accelerations (from 1 to 5g), which are the performances required by High Speed Machining. PKMs are said to be very accurate, which is not true in every case4, but another advantage is that the struts only work in traction or compression. However, there are many structural differences between serial and parallel machine tools, which makes it hard to strictly compare their performances. 3.3. Problems with PKMs a) The workspace of a PKM has not a simple geometric shape, and its functional volume is reduced, compared to the space occupied by the machine7, as we can see on Fig. 5 Figure 5. Workspace sections of Tricept 805 b) For a serial mechanism, the velocity and force transmission ratios are constant in the workspace. For a parallel mechanism, in contrast, these ratios may vary significantly in the workspace because the displacement of the tool is not linearly related to the displacement of the actuators. In some parts of the workspace, the maximal velocities and forces measured at the tool may differ significantly from the maximal velocities and forces that the actuators can produce. This is particularly true in the vicinity of THE DESIGN OF PKMT USING KINETOSTATIC PERFORMANCE CRITERIA 5 singularities. At a singularity, the velocity, accuracy and force ratios reach extreme values. c) Calibration of PKMs is quite complicated because of kinematic models complexity8. 4. EXISTING PKMT DESIGNS In this section will be presented some existing PKMTs. 4.1. Fully Parallel Machine Tools What we call fully parallel machine tools are PKMs that have as many degrees of freedom as struts. On Fig. 7, we can see a 3-RPR fully parallel mechanism with three struts. Each strut is made of a revolute joint, a prismatic actuated joint and a revolute joint. Figure 6. 3-RPR fully parallel mechanism Fully PKMT with six variable length struts are called hexapods. Hexapods are inspired by the Gough Platform. The first PKMT was the hexapod “Variax” from Giddings and Lewis presented in 1994 at the IMTS in Chicago. Hexapods have six degrees of freedom. One more recent example is the CMW300, a hexapod head designed by the Compagnie Mécanique des Vosges (Figure 7) . Figure 7. Hexapod CMW 300 (perso.wanadoo.fr/cmw.meca.6x/6AXES.htm) Fully parallel machine tools with fixed length struts can have three, four or six legs. The Urane SX (Figures8 and 13) from Renault Automation is a three leg machine, whose tool can only move along X, Y and Z axes, and its architecture is inspired from the Delta robot9, designed for pick and place applications. The Hexa M from Toyoda is a PKMT with six fixed length struts (Figure 9). Figure 8. Renault automation Urane SX (from “Renault Automation Magazine”, n° 21, may 1999) Figure 9. Toyoda Hexa M (www.toyodakouki. co.jp) 4.2. Other Kinds of PKMT The Tricept 805 is a widely used PKMT with three variable length struts (Figures 5 and 10). The Tricept 805 has a hybrid architecture: a two degrees of freedom wrist serially mounted on a tripod architecture. Another non fully parallel MT is the Eclipse (Figure 11) from Sena Technology10, 11. The Eclipse is an overactuated PKM for rapid machining, capable of simultaneous five faces milling, as well as turning, thanks to the second spindle. Figure 10. Tricept 805 from Neos robotics (www.neosrobotics.com) Figure 11. The Eclipse, from Sena Technology (macea.snu.ac.kr/eclipse/homepage.html) 5. DESIGNING A PKMT 5.1. A Global Task Given a set of needs, the most adequate machine will be designed through a set of design parameters like the machine morphology (serial, parallel or hybrid kinematic structure), the machine geometry (link dimensions, joint orientation and joint ranges), the type of actuators (linear or rotative motor), the type of joints (prismatic or revolute), the number and the type of degrees of freedom, the task for which the machine is designed. These parameters must be defined using relevant design criteria. 5.2. Kinetostatic Performance Criteria are Adequate for the Design of PKMTs The only way to cope with problems due to singularities is to integrate kinetostatic performance criteria in the design process of a PKMT. Kinetostatic performance criteria evaluate the ability of a mechanism to transmit forces or velocities from the actuators to the tool. These kinetostatic performance criteria must be able to guaranty minimum stiffness, accuracy and velocity performances along every direction throughout the workspace of the PKMT. To reach this goal, we use two complementary criteria: the conditioning of the Jacobian matrix J of the PKMT, called conditioning index, and the manipulability ellipsoid associated with J12. The Jacobian matrix J relates the joint rates to the tool velocities. It also relates the static tool efforts to the actuator efforts. The conditioning index is defined as the ratio between the highest and the smallest eigenvalue of J. The conditioning index varies from 1 to infinity. At a singularity, the index is infinity. It is 1 at another special configuration called isotropic configuration. At this configuration, the tool velocity and stiffness are equal in all directions. The conditioning index measures the uniformity of the distribution of the velocities and efforts around one given configuration but it does not inform about the magnitude of the velocity amplification or effort factors. The manipulability ellipsoid is defined from the matrix (J JT)-1. The principal axes of the ellipsoid are defined by the eigenvectors of (J JT)-1 and the lengths of the principal axes are the square roots of the eigenvalues of (J JT)-1. The eigenvalues are associated with the velocity (or force) amplification factors along the principal axes of the manipulability ellipsoid. These criteria are used in Wenger13, to optimize the workspace shape and the performances uniformity of the Orthoglide, a three degree of freedom PKM dedicated to milling applications (Figure 12). Figure 12. A section of Orthoglide’s optimised workspace 5.3. Technical Problems If the struts of the PKMT are made with ballscrews, the PKMT accuracy may suffer from struts warping due to heating caused by frictions generated by ballscrews. This problem is met by hexapods designers that use ballscrews. Thus, besides manufacturing inaccuracies, the calibration of a PKMT will have to take into account dimensions variations due to dilatation. A good thermal evacuation can minimise the effects of heating. In case PKMT actuators are linear actuators, magnetic pollution has to be taken into account so that chips clearing out is not obstructed. One technique, used by Renault Automation for the Urane SX, is to isolate the tool from the mechanism. At last, choosing fixed length or variable length struts influence the behaviour of the machine. Actuators have to be mounted on the struts in case of variable length struts, which increases moved masses. Fixed length struts do not have this problem, and furthermore allow the use of linear actuators, that bring high dynamic performances. 6. CONCLUSIONS The aim of this article was to introduce a few criteria for the design of PKMTs, which may become interesting alternatives for High Speed Machining, especially in the milling of large parts made of hard material, or for serial manufacturing operations on aeronautical parts. Kinetostatic criteria seem to be well adapted to the design of PKMTs, particularly for the kinematic design and for the optimisation of the workspace shape, with regard to performances uniformity. The kinetostatic criteria have been used for the design of the Orthoglide, a three-axis PKMT developed at IRCCyN. A small scale prototype is under development. A five-axis PKMT will be derived from the Orthoglide. 設計并聯機床 使用kinetostatic標準 的表現 http://arxiv.org/ftp/arxiv/papers/0705/0705.1038.pdf 1 介紹 多數工業機床有一個串行運動學架構，這意味著每個軸進行下列工作時，包括其執行機構和聯接點高速加工突出了一些弊端，例如架構：較重的運動部件需要從機械結構高剛度，以限制彎曲問題，即降低機床精度，并限制動態表現的曲線。 這就是為什么并聯機床吸引了越來越多的研究人員和公司，因?yàn)樗鼈儞?jù)稱提供了單獨的優勢，如高結構剛度和高動態的能力。事實上，并聯安排的聯系，可提供更高的剛度和較低的誤差，減少慣性的影響。因此，并聯機床有更好的動態性能。然而，設計一個并聯機床是一個艱巨的任務，在進一步的研究之前，廣泛地在工業用途中的調研，是必不可少的。 許多標準要考慮到在設計一個并聯機床。我們要特別注意描述并聯機床標準依賴于現有的雅可比矩陣的機制。該組織的這份文件具體內容如下：未來介紹總論約并聯機床，那就是解釋了為什么并聯機床是不可替代機床的設計。一個設計中的應用了一次小規模的機床樣機研制irccyn。 2 關于并聯機床 2.1 總論 第一次工業應用并聯機床是The Gough平臺（圖1 ） 設計于1957年，以測試tyres1 。并聯機床當時已使用多年，在飛行模擬器和機器人applications2因?yàn)樗麄兊牡鸵苿?dòng)質量和高動態表演。由于發展的高速切削加工，并聯機床已成為有趣的替代機床。 圖1 The Gough platform 隨著高速切削的不斷發展，傳統串聯式機構構造平臺的結構剛性與移動臺高速化逐漸成為技術發展的瓶頸，而并聯式平臺便成為最佳的候選對象，而相對于串聯式機床來說，并聯式工作平臺具有如下特點和優點： (1) 結構簡單、價格低 機床機械零部件數目較串聯構造平臺大幅減少，主要由滾珠絲杠、虎克鉸、球鉸、伺服電機等通用組件組成，這些通用組件可由專門廠家生產，因而本機床的制造和庫存成本比相同功能的傳統機床低得多，容易組裝和搬運。 (2) 結構剛度高 由于采用了封閉性的結構(closed-loop structure)使其具有高剛性和高速化的優點，其結構負荷流線短，而負荷分解的拉、壓力由六只連桿同時承受，以材料力學的觀點來說，在外力一定時，懸臂量的應力與變形都最大，兩端插入(build-in)次之，再來是兩端簡支撐(simply-supported)，其次是受壓的二力結構，應力與變形都最小的是受張力的二力結構，故其擁有高剛性。其剛度重量比高于傳統的數控機床。 (3) 加工速度高，慣性低 如果結構所承受的力會改變方向，(介于張力與壓力之間)，兩力構件將會是最節省材料的結構，而它的移動件重量減至最低且同時由六個致動器驅動，因此機器很容易高速化，且擁有低慣性。 (4) 加工精度高 由于其為多軸并聯機構組成，六個可伸縮桿桿長都單獨對刀具的位置和姿態起作用，因而不存在傳統機床(即串聯機床)的幾何誤差累積和放大的現象，甚至還有平均化效果(averaging effect)；其擁有熱對稱性結構設計，因此熱變形較?。还仕哂懈呔鹊膬?yōu)點。 (5) 多功能靈活性強 由于該機床機構簡單控制方便，較容易根據加工對象而將其設計成專用機床，同時也可以將之開發成通用機床，用以實現銑削、鏜削、磨削等加工，還可以配備必要的測量工具把它組成測量機，以實現機床的多功能。這將會帶來很大的應用和市場前景，在國防和民用方面都有著十分廣闊的應用前景。 (6) 使用壽命長 由于受力結構合理，運動部件磨損小，且沒有導軌，不存在鐵屑或冷卻液進入導軌內部而導致其劃傷、磨損或銹蝕現象。 (7) Stewart平臺適合于模塊化生產 對于不同的機器加工范圍，只需改變連桿長度和接點位置，維護也容易，無須進行機件的再制和調整，只需將新的機構參數輸入。 (8) 變換座標系方便 由于沒有實體座標系，機床座標系與工件座標系的轉換全部靠軟件完成，非常方便。 Stewart平臺應用于機床與機器人時，可以降低靜態誤差(因?yàn)楦邉傂?，以及動態誤差(因?yàn)榈蛻T量)。而Stewart平臺的劣勢在于其工作空間較小，且其在工作空間上有著奇異點的限制，而串聯工作平臺，控制器遇到奇異點時，將會計算出驅動裝置無法達成的驅動命令而造成控制誤差，但Stewart平臺在奇異位置會失去支撐部分方向的力或力矩的能力，無法完成固定負載對象。 在并聯機床，工具是以底座作為支撐做伸縮性運動，下圖為伸縮運動簡圖。一